And finally the throughput comparison of IPv6 and legacy IP on a Juniper ScreenOS firewall. Nobody needs this anymore since they are all gone. ;) But since I did the same speedtests for Palo Alto and FortiGates I was interested in the results here as well.
Continue reading Juniper ScreenOS IPv4 vs. IPv6 Throughput Tests →
Just for fun some more VPN throughput tests, this time for the late Juniper ScreenOS firewalls. I did the same iperf TCP tests as in my labs for Fortinet and Palo Alto, while I was using six different phase1/2 proposals = crypto algorithms. The results were as expected with one exception.
Continue reading Juniper ScreenOS VPN Speedtests →
A few weeks ago I swapped a FortiGate 100D firewall to a 90D firewall. The 100D was defective and needed to be replaced. Since the customer only has a 20 Mbps ISP connection, I thought that a FortiGate 90D would fit for the moment, since it has a firewall throughput of 3,5 Gbps, compared to the lower value of 2,5 Gbps from the 100D.
Indeed, it worked. However, the CPU usage increase was huge, almost related to the NGFW throughput. Here are some graphs:
Continue reading CPU Usage Increase FortiGate 100D -> 90D →
Once more some throughput tests, this time the Palo Alto Networks firewalls site-to-site IPsec VPN. Similar to my VPN speedtests for the FortiGate firewall, I set up a small lab with two PA-200 firewalls and tested the bandwidth of different IPsec phase 2 algorithms. Compared to the official data sheet information from Palo Alto that state an IPsec VPN throughput of 50 Mbps, the results are really astonishing.
Continue reading Palo Alto VPN Speedtests →
After I have done some speedtests on the FortiGate firewall I was interested in doing the same tests on a Palo Alto. That is: What are the throughput differences of IPv4 vs. IPv6, measured with and without security profiles, i.e., with and without threat prevention.
It turned out that the throughput is much higher than the official information from Palo Alto. Furthermore, I was not able to test the threat prevention at all, because non of my traffic (iperf and mere HTTP) went through the antivirus engines. I have to test this again. However, here are the measured values so far:
Continue reading Palo Alto IPv4 vs. IPv6 Performance Speedtests →
I was interested in the performance of my FortiGate firewall when comparing IPv4 and IPv6 traffic. Therefore I built a small lab consisting a FortiWiFi 90D firewall and two Linux clients running iperf. I tested the network throughput for both Internet Protocols in both directions within three scenarios: 1) both clients plugged into the same “hardware switch” on the FortiGate, 2) different subnets with an “allow any any” policy without any further security profiles, and finally, 3) activating antivirus, application control, IPS, and SSL inspection.
Continue reading FortiGate IPv4 vs. IPv6 Performance Speedtests →
Ähnlich zum dem Site-to-Site VPN Throughput Test der FortiGate Firewalls wollte ich mal den FRITZ!Boxen auf den Zahn fühlen und herausfinden, in wie fern sich der VPN-Durchsatz bei den Modellen unterscheidet, bzw. welche Rolle die ausgewählten Verschlüsselungsverfahren spielen. Getestet habe ich eine (etwas ältere) FRITZ!Box 7270v3 mit FRITZ!OS 06.06 sowie eine (neuere, obgleich nicht Topmodell) FRITZ!Box 7430 in Version 06.30. Als VPN-Endpunkt auf der Gegenseite habe ich eine FortiGate Firewall genommen. Getestet wurde das reine Routing/NATting sowie verschiedene Phase 2 Proposals mit dem Netzwerk Tool iperf.
Continue reading FRITZ!Box VPN Speedtests →
Triggered by a customer who had problems getting enough speed through an IPsec site-to-site VPN tunnel between FortiGate firewalls I decided to test different encryption/hashing algorithms to verify the network throughput. I used two FortiWiFi 90D firewalls that have an official IPsec VPN throughput of 1 Gbps. Using iperf I measured the transfer rates with no VPN tunnel as well as with different IPsec proposals.
I first ran into really slow performances which were related to the default “Software Switch” on the FortiGate. After deleting this type of logical switch, the VPN throughput was almost as expected.
Continue reading FortiGate VPN Speedtests →
A common mistake when analyzing network speed/bandwidth between different applications and servers is to fully rely on the mere size of the files being transferred. In fact, one big file will transfer much faster than thousands of small files that have the same accumulated size. This depends on the overhead of reading/writing these files, building TCP/IP sessions, scanning them for viruses, etc. Furthermore, it is application dependent.
I built a small lab with an FTP server, switch, firewall, and an FTP client in which I played a bit with different file sizes. In this blog post I am showing the measured transfer times and some Wireshark graphs.
Continue reading Network Transfer: 1 Big vs. 100 Small Files →