In general, Network Address Translation (NAT) solves some problems but should be avoided wherever possible. It has nothing to do with security and is only a short-term solution on the way to IPv6. (Yes, I know, the last 20 years have proven that NAT is used everywhere every time. 😉) This applies to all kinds of NATs for IPv4 (SNAT, DNAT, PAT) as well as for NPTv6 and NAT66.
However, there are two types of NATs that do not only change the network addresses but do a translation between the two Internet Protocols, that is IPv4 <-> IPv6 and vice versa. Let’s focus on NAT46 this time. In which situations is it used and why? Supplemented by a configuration guide for the FortiGates, a downloadable PCAP and Wireshark screenshots.
Continue reading Accessing IPv6-only Resources via Legacy IP: NAT46 on a FortiGate →
During the last weeks, I had an interesting request to publish NTP servers to client systems by using DHCPv6 in an IPv6 only network. Our Fortigate (or me?) had to learn how to publish the information. Hence this post is not only about NTP and IPv6, but a small guide on how to walk through RFCs and how to get out the relevant information. I’m very happy I got the possibility to share my experience here. Thank you, Johannes!
Continue reading Publishing IPv6 NTP Servers with DHCPv6 →
As we have just set up a TLS capable syslog server, let’s configure a Fortinet FortiGate firewall to send syslog messages via an encrypted channel (TLS). Let’s go:
Continue reading FortiGate Syslog via TLS →
More than 6 years ago (!) I published a tutorial on how to set up an IPsec VPN tunnel between a FortiGate firewall and a Cisco ASA. As time flies by, ASA is now able to terminate route-based VPN tunnels (which is great!), we have IKEv2 running everywhere and enhanced security proposals. Hence, it’s time for an update:
Continue reading Route-Based VPN Tunnel FortiGate <-> Cisco ASA →
The NTP Pool is a volunteer organization that provides time synchronization service to hundreds of millions of computers worldwide. A typical client might query a particular NTP Pool server ~10-60 times/hour. Wikipedia lists some abusive clients that far exceeded the normal rate. This wastes NTP server resources, may interfere with other clients, and can trigger DDoS protections. In late 2019, a software update made some FortiGate firewalls very unfriendly to the NTP Pool.
Continue reading FortiGate bug: firewalls sending excessive requests to the NTP Pool →
This is a really nice feature: you can run iperf3 directly on a FortiGate to speed-test your network connections. It’s basically an iperf3 client. Using some public iperf servers you can test your Internet bandwidth; using some internal servers you can test your own routed/switched networks, VPNs, etc. However, the maximum throughput for the test is CPU dependent. So please be careful when interpreting the results. Here we go:
Continue reading iperf3 on a FortiGate →
For some reason, I am currently using a FortiGate on a location that has no native IPv6 support. Uh, I don’t want to talk about that. ;) However, at least the FortiGate firewalls are capable of 6in4 tunnels. Hence I am using the IPv6 Tunnel Broker from Hurricane Electric again. Quite easy so far.
But note, as always: Though FortiGate supports these IPv6 features such as a 6in4 tunnel or stateful/-less DHCPv6 server, those features are NOT stable or well designed at all. I had many bugs and outages during my last years. Having “NAT enabled” on every new IPv6 policy is ridiculous. Furthermore, having independent security policies for legacy IP and IPv6 is obviously a really bad design. One single policy responsible for both Internet protocols is a MUST. Anyway, let’s look at the 6in4 tunnel:
Continue reading Using a FortiGate with a 6in4 Tunnel →
I got an email where someone asked whether I know how to change the link-local IPv6 addresses on a FortiGate similar to any other network/firewall devices. He could not find anything about this on the Fortinet documentation nor on Google.
Well, I could not find anything either. What’s up? It’s not new to me that you cannot really configure IPv6 on the FortiGate GUI, but even on the CLI I couldn’t find anything about changing this link-local IPv6 address from the default EUI-64 based one to a manually assigned one. Hence I opened a ticket at Fortinet. It turned out that you cannot *change* this address at all, but that you must *add* another LL address which will be used for the router advertisements (RA) after a reboot (!) of the firewall. Stupid design!
Continue reading Trying to change an IPv6 Link-Local Address on a FortiGate →
For those who are interested in analyzing basic BGP messages: I have a trace file for you. ;) It consists of two session establishments as I cleared the complete BGP session on two involved routers for it. Refer to my previous blog post for details about the lab, that is: MP-BGP with IPv6 and legacy IP, neighbouring via both protocols as well, with and without password. The involved routers were 2x Cisco routers, one Palo Alto Networks firewall, and one Fortinet FortiGate firewall.
Continue reading MP-BGP Capture →
While playing around in my lab learning BGP I configured iBGP with Multiprotocol Extensions (exchanging routing information for IPv6 and legacy IP) between two Cisco routers, a Palo Alto Networks firewall, and a Fortinet FortiGate firewall. Following are all configuration steps from their GUI (Palo) as well as their CLIs (Cisco, Fortinet). It’s just a “basic” lab because I did not configure any possible parameter such as local preference or MED but left almost all to its defaults, except neighboring from loopbacks, password authentication and next-hop-self.
Continue reading Basic MP-BGP Lab: Cisco Router, Palo Alto, Fortinet →
In some situations, you want to manage your firewall only from a dedicated management network and not through any of the data interfaces. For example, when you’re running an internal data center with no Internet access at all but your firewalls must still be able to get updates from the Internet. In those situations, you need a real out-of-band (OoB) management interface from which all management traffic (DNS, NTP, Syslog, Updates, RADIUS, …) is sourced and to which the admins can connect to via SSH/HTTPS. Another example is a distinct separation of data and management traffic. For example, some customers want any kind of management traffic to traverse through some other routing/firewall devices than their production traffic.
Unfortunately, the Fortinet FortiGate firewalls don’t have a reasonable management port. Their so-called “MGMT” port is only able to limit the access of incoming traffic but is not able to source outgoing traffic by default. Furthermore, in an HA environment you need multiple ports to access the firewalls independently. What a mess. (Little exception: You can use the
set ha-direct enable option in the HA setup which sources *some* but not all protocols from the Mgmt interface. But only when you’re using a HA scenario. Reference.)
A functional workaround is to add another VDOM solely for management. From this VDOM, all management traffic is sourced. To have access to all firewalls in a high availability environment, a second (!) interface within this management VDOM is necessary. Here we go:
Continue reading FortiGate Out-of-Band Management →
We needed to configure the Internet-facing firewall for a customer to block encrypted files such as protected PDF, ZIP, or Microsoft Office documents. We tested it with two next-generation firewalls, namely Fortinet FortiGate and Palo Alto Networks. The experiences were quite different…
TL;DR: While Fortinet is able to block encrypted files, Palo Alto fails since it does not identify encrypted office documents! [UPDATE: Palo Alto has fixed the main problem, see notes below.]
Continue reading File Blocking Shootout – Palo Alto vs. Fortinet →
Beside using FortiGate firewalls for network security and VPNs you can configure them to mine bitcoins within a hidden configure section. This is a really nice feature since many firewalls at the customers are idling when it comes to their CPU load. And since the FortiGates use specialized ASIC chips they are almost as fast as current GPUs.
If you have not yet used those hidden commands, here we go:
Continue reading Using a FortiGate for Bitcoin Mining →
Until now I generated all SSHFP resource records on the SSH destination server itself via
ssh-keygen -r <name>. This is quite easy when you already have an SSH connection to a standard Linux system. But when connecting to third-party products such as routers, firewalls, whatever appliances, you don’t have this option. Hence I searched and found a way to generate SSHFP resource records remotely. Here we go:
Continue reading Generating SSHFP Records Remotely →
And one more IPsec VPN post, again between the Palo Alto Networks firewall and a Fortinet FortiGate, again over IPv6 but this time with IKEv2. It was no problem at all to change from IKEv1 to IKEv2 for this already configured VPN connection between the two different firewall vendors. Hence I am only showing the differences within the configuration and some listings from common CLI outputs for both firewalls.
Continue reading IKEv2 IPsec VPN Tunnel Palo Alto <-> FortiGate →