Tag Archives: Fortinet

IPv6 IPsec VPN Tunnel Palo Alto <-> FortiGate

Fortinet, IPsec/VPN, IPv6, Palo Alto Networks, , , , ,

Towards the global IPv6-only strategy ;) VPN tunnels will be used over IPv6, too. I configured a static IPsec site-to-site VPN between a Palo Alto Networks and a Fortinet FortiGate firewall via IPv6 only. I am using it for tunneling both Internet Protocols: IPv6 and legacy IP.

While it was quite easy to bring the tunnel “up”, I had some problems tunneling both Internet Protocols over the single phase 2 session. The reason was some kind of differences within the IPsec tunnel handling between those two firewall vendors. Here are the details along with more than 20 screenshots and some CLI listings.

Continue reading IPv6 IPsec VPN Tunnel Palo Alto <-> FortiGate →

Palo vs. Forti: Blog Stats

Commentary, Fortinet, Palo Alto Networks, , ,

I want to talk about a fun fact concerning my blog statistics: Since a few years I have some “CLI troubleshooting commands” posts on my blog – one for the Palo Alto Networks firewall and another for the FortiGate firewall from Fortinet. If you are searching on Google for something like “palo alto cli commands” or “fortigate troubleshooting cli” my blog is always listed amongst the first 2-4 results.

But for some reasons the article for Fortinet has much more hits. I don’t know why but I have two different ideas. What do you think?

Continue reading Palo vs. Forti: Blog Stats →

CPU Usage Increase FortiGate 100D -> 90D

Fortinet, Monitoring, , , , ,

A few weeks ago I swapped a FortiGate 100D firewall to a 90D firewall. The 100D was defective and needed to be replaced. Since the customer only has a 20 Mbps ISP connection, I thought that a FortiGate 90D would fit for the moment, since it has a firewall throughput of 3,5 Gbps, compared to the lower value of 2,5 Gbps from the 100D.

Indeed, it worked. However, the CPU usage increase was huge, almost related to the NGFW throughput. Here are some graphs:

Continue reading CPU Usage Increase FortiGate 100D -> 90D →

Fortinet Feature Requests

Fortinet, , , ,

I really like the FortiGate firewalls. They are easy to manage and have lots of functionality. However, I am also aware of some other firewall products and therefore have some feature requests to Fortinet that are not currently implemented in their firewalls. I am sometimes forwarding these FRs to the Fortinet support or to a SE, but they are not really interested in that. ;( So here is a list of my ideas that could improve the firewall. Hopefully/maybe some of them will be implemented one day…

Continue reading Fortinet Feature Requests →

FortiGate Virtual IPs without Reference

Fortinet, NAT, , , , , ,

Migrating from Juniper ScreenOS firewalls to FortiGates, there are some differences to note with static NATs, i.e., Mapped IPs (MIPs) on a Netscreen and Virtual IPs (VIPs) on a FortiGate. While the Juniper MIPs on an interface are always used by the firewall whenever a packet traverses the interface, the virtual IP objects on a FortiGate must be used at least once in the security policy before they are really used by the firewall.

Continue reading FortiGate Virtual IPs without Reference →

FortiGate Virtual IPs with Interface “Any”

Fortinet, NAT, , , , , ,

On the FortiGate firewall, address objects and virtual IPs (VIPs) can be set up with an interface. For address objects this has no technical relevance – the address objects simply only appear on policies if the appropriate interface is selected. But for virtual IPs, this setting has relevance on how connections are NATed. This can be problematic.

Continue reading FortiGate Virtual IPs with Interface “Any” →

FortiGate IPv4 vs. IPv6 Performance Speedtests

Bandwidth/Delay, Fortinet, IPv6, , , , , , ,

I was interested in the performance of my FortiGate firewall when comparing IPv4 and IPv6 traffic. Therefore I built a small lab consisting a FortiWiFi 90D firewall and two Linux clients running iperf. I tested the network throughput for both Internet Protocols in both directions within three scenarios: 1) both clients plugged into the same “hardware switch” on the FortiGate, 2) different subnets with an “allow any any” policy without any further security profiles, and finally, 3) activating antivirus, application control, IPS, and SSL inspection.

Continue reading FortiGate IPv4 vs. IPv6 Performance Speedtests →

FortiGate VPN Speedtests

Bandwidth/Delay, Fortinet, IPsec/VPN, , , , , ,

Triggered by a customer who had problems getting enough speed through an IPsec site-to-site VPN tunnel between FortiGate firewalls I decided to test different encryption/hashing algorithms to verify the network throughput. I used two FortiWiFi 90D firewalls that have an official IPsec VPN throughput of 1 Gbps. Using iperf I measured the transfer rates with no VPN tunnel as well as with different IPsec proposals.

I first ran into really slow performances which were related to the default “Software Switch” on the FortiGate. After deleting this type of logical switch, the VPN throughput was almost as expected.

Continue reading FortiGate VPN Speedtests →

FortiGate: Software-/ Hardware-/ VLAN-Switch

Fortinet, , , ,

I am still a bit confused about the different switch types a FortiGate firewall is able to handle. While there is a lot of information on the Internet about the “internal-switch-mode” of “switch/interface“, I have not found any good information about the differences between the “Hardware/Software/VLAN” switch types that are configured via the GUI or via the “virtual-switch-vlan enable” CLI command. Though I still don’t know exactly all differences, I am trying to explain some of them here.

Continue reading FortiGate: Software-/ Hardware-/ VLAN-Switch →

Tufin SecureTrack: Adding Devices

Tufin, Tutorial/Howto, , , , , , , , ,

Since a few weeks I am using Tufin SecureTrack in my lab. A product which analyzes firewall policies about their usage and their changes by administrators (and much more). Therefore, the first step is to connect the firewalls to SecureTrack in two directions: SSH from SecureTrack to the device to analyze the configuration, as well as Syslog from the device to SecureTrack to real-time monitor the policy usage.

This blog post shows the adding of the following firewalls into Tufin: Cisco ASA, Fortinet FortiGate, Juniper ScreenOS, and Palo Alto PA.

Continue reading Tufin SecureTrack: Adding Devices →

MRTG/Routers2: Template FortiGate

Fortinet, MRTG/Routers2, Template, , , , , ,

A few weeks ago I constructed an MRTG/Routers2 template for the Fortinet FortiGate firewalls. I am using it for monitoring the FortiGate from my MRTG/Routers2 server. With the basic MRTG tool “cfgmaker” all graphs for the interfaces are generated automatically. My template is an add-on that appends graphs for CPU, memory, and disk usage, as well as connections and VPN statistics. Furthermore, it implements the ping statistics graph and a “short summary”, which only shows the system relevant graphs.

Continue reading MRTG/Routers2: Template FortiGate →

CLI Commands for Troubleshooting FortiGate Firewalls

Fortinet, Memorandum, , , , , ,

This blog post is a list of common troubleshooting commands I am using on the FortiGate CLI. It is not complete nor very detailled, but provides the basic commands for troubleshooting network related issues that are not resolvable via the GUI. I am not focused on too many memory, process, kernel, etc. details. These must only be used if there are really specific problems. I am more focused on the general troubleshooting stuff. I am using it personally as a cheat sheet / quick reference and will update it from time to time.

Continue reading CLI Commands for Troubleshooting FortiGate Firewalls →

Basic IPv6 Configuration on a FortiGate Firewall

Fortinet, IPv6, Memorandum, Template, , , , , , ,

It’s really great that the FortiGate firewalls have a DHCPv6 server implemented. With this mandatory service, IPv6-only networks can be deployed directly behind a FortiGate because the stateless DHCPv6 server provides the DNS server addresses. (This is unlike Palo Alto or Cisco which have no DHCPv6 server implemented.)

UPDATE: In the meantime Fortinet has implemented the RDNSS and DNSSL options as well. Great. Hence you don’t need DHCPv6 at all anymore to run an IPv6-only network. I updated my listings below as well.

However, the configuration on the FortiGate is really bad because nothing of the IPv6 features can be set via the GUI. (And this is called a Next-Generation Firewall? Not only the features count, but also the usability!) Everything must be done through the CLI which is sometimes hard to remember. Therefore I am publishing this memo of the appropriate CLI configuration commands.

Continue reading Basic IPv6 Configuration on a FortiGate Firewall →